37 found, showing page 1 of 3
FLOW-GAURD 8OZ
Medium-Bodied CPVC Resin In Solvent Solution Formula For Copper Tube Size (CTS) CPVC Hot And Cold Potable Water Pipe And Fittings Up To 2" Diameter Interference Fit Only And Systems Up To 180 Degrees Fahrenheit. Faster Cure Time/Reduced Installation Time. May Be Used Without Primer Where Local Codes Permit. Low VOC With Reduced Solvent Emissions. Exceeds New Environmental Requirements, Meets Various California District Rules And ASTM F-493.
- Lo-VOC
- 1-Step - Yellow
- Flow-Guard Gold
- Size Ozs. : 8
- For Copper Tube Size (CTS) CPVC Hot And Cold Potable Water Pipe And Fittings Up-To 2 In Dia Interference Fit
- May Be Used Without Primer Where Local Coders Permit
- Flowguard Gold Is A Registered Trademark Of The Lubrizol Corporation
View Details
Call for Price
PVC ELECTRICAL CEMENT 8OZ
Recommended For All Grades And Types Of Carlon PVC Conduit, Duct, Wireway, And Fittings Except Flex-Plus Blue Up To 6" Diameter. Can With Dauber Applicator.
- Gray Solvent Cement
- Regular Grade
- Size Oz : 8
View Details
Call for Price
1.7 OZ SOLDER PASTE FLUX
Will Not Freeze Or Decompose. No Odor. Lead Free. Recommended For Use On All Solder Alloys Including 95/5 And All Lead Free Solders. Meets Specification O-F-506, Type 1A And A-A-51145, MIL-F-4995-2.
- Regular
- Brand:"NOKORODE"
- Size Ozs. : 1.7
View Details
Call for Price
PIPE THREAD SEALANT 1/4 PT
Soft-Set, Slow Drying Compound Seals, Lubricates, Protects Threaded Pipe And Fittings. Can Be Pressurized Immediately For Piping Up Through 2" And 100 Psi. Recommended For Use On Threaded Galvanized Steel, Iron, Brass, Copper, Aluminum, Stainless Steel, Polyethylene, Fiberglass Reinforced, And PVC Pipe. Conforms To TT-S-1932.
- No. 5
- Size Ozs. : 1.75
- Lead Free And Contains No Other Metals
- Soft-Setting, Slow Drying
- Will Not Dry Out In The Can
- Economical - Requires Only A Small Amount
- Lubricates And Protects Threads
- Reduces Friction To Allow Tighter Joint Makeup
- Permits Easy Break Out With No Damage To Threads
View Details
Call for Price
CLEAR PIPE CLEANER 16OZ
For Plastic Pipes And Fittings, All Schedules And All Diameters. A Fast-Acting Cleaner To Remove Surface Dirt, Grease And Grime. Flows Freely And Evaporates Quickly. Does Not Penetrate Pipe Surface.
- Lo-VOC
- All Purpose - Clear
- Yellow Label
- Size Ozs. : 16
- Lo-V. O. C. Solvent Cement Meets SCAQMD 1171/316A Or BAAQMD Method 40 And Various Environmental Requirements
- All Schedules And All Diameters
- Flows Freely And Evaporates Quickly
- Fast Acting Cleaner Removes Surface Dirt, Grease And Grime
View Details
Call for Price
CLEAR PIPE CLEANER 32OZ
All-Purpose Pipe Cleaner Designed To Thoroughly Clean Pipe. Can Be Used On ABS, CPVC, And PVC Pipe And Fittings. Apply At Temperatures From 40 Degrees To 110 Degrees Fahrenheit. Flows Freely And Evaporates Quickly. Dauber Can.
- All Purpose - Clear
- Size Ozs. : 32
- Low-VOC Solvent Cement
- Fast Acting Cleaner Removes Surface Dirt, Grease And Grime From The Pipe Surface
- Apply Sparingly To ABS Pipe And Fittings
View Details
Call for Price
8-OZ PURPLE PRIMER NSF
A Purple-Tinted Aggressive Primer Recommended For Use On PVC And CPVC Pipe And Fittings, All Schedules And Diameters. Formulated To Remove Surface Dirt, Grease And Grime As Well As Soften The Pipe Surface To Allow For A Fast, Secure And Permanent Solvent Weld. For Use In Areas Where The Code Calls For Verification That A Primer Has Been Used. Recommended For All PVC And CPVC Installations. NSF Listed. Meets ASTM F-656.
- Purple Primer
- LO-VOC
- Size Ozs. : 8
- Purple-Tinted Aggressive Primer For Use On PVC And CPVC Pipe And Fittings - Lo-V.O.C. Primer Meets California South Coast Air Quality Management District (SCAQMD) 1168/316A Or BAAQMD Method 40 And Various Environmental Requirements
- For Use In Areas Where Plumbing Code Calls For Verification That A Primer Has Been Used
View Details
Call for Price
8 Oz. All-Purpose Glue
Medium-Bodied Milky Clear Cement For ABS, PVC, Or CPVC Up To 6" Diameter. Recommended For Pipe And Fittings Schedule 40 And Schedule 80, Potable Water, Pressure Pipe, Gas, Conduit, And DWV. Recommended Application Temperature 40 Degrees F To 110 Degrees F. Meets Performance Requirements Of ASTM D-2564, D-2235, F-493. Check Local Codes For Acceptability Of This Product.
- For ABS, PVC, and CPVC Pipe Fittings
- Red Label - Lo-VOC
- Size Ozs. : 8
- For Use On All Schedules And Classes Of ABS, PVC And CPVC Pipe And Fittings Up-To 6 In Diameter With Interference Fit
- Check Local Codes For Acceptability Of This Product
View Details
Call for Price
8-OZ HEAVEY DUTY GLUE GREEN
Heavy-Bodied Clear Cement For PVC Pipe And Fittings. Up To 12" Diameter For Schedule 40 And Schedule 80. Recommended For ALL Grades And Types Of PVC Pipe And Fittings, Potable Water, Pressure Pipe, Gas, Conduit And DWV. Helps Fill Gaps In Larger Diameter Pipe And Loose Fitting Joints. Apply At Temperatures 40 Degrees Fahrenheit To 110 Degrees Fahrenheit. Exceeds ASTM D-2564. NSF And UPC Listed.
- Heavy Duty - Clear
- Lo-VOC
- Size Ozs. : 8
- For Use On All Schedules And Classes PVC Pipe And Fitting Up-To 12 In Dia With Interference Fit, Up-To 18 In For Non-Pressure
- Thick Formula Fills Gaps In Large Diameter Pipe And Loose Fitting Joints
View Details
Call for Price
16 Oz. All-Purpose Glue
Medium-Bodied Milky Clear Cement For ABS, PVC, Or CPVC Up To 6" Diameter. Recommended For Pipe And Fittings Schedule 40 And Schedule 80, Potable Water, Pressure Pipe, Gas, Conduit, And DWV. Recommended Application Temperature 40 Degrees F To 110 Degrees F. Meets Performance Requirements Of ASTM D-2564, D-2235, F-493. Check Local Codes For Acceptability Of This Product.
- For ABS, PVC, and CPVC Pipe Fittings
- Red Label - Low VOC
- Size Ozs. : 16
- For Use On All Schedules And Classes Of ABS, PVC And CPVC Pipe And Fittings Up-To 6 In Diameter With Interference Fit
- Check Local Codes For Acceptability Of This Product
View Details
Call for Price
1 Lb. Duct Seal Insulator
Malleable non-conductive compound for sealing of electrical raceway connections from air, noise and moisture.
- Color: Dark Gray
- Temperature Rating: -20 to 35 deg F
View Details
Call for Price
8 Oz. PRO DOPE Gray Thread Sealant
Standard Oil-Based Thread Sealant Ensures Exceptional Leak-Proof Joints. For Use On Metal Pipe And Fittings Carrying Water, Natural Gas, Air, Steam, Ammonia, Brine, Diluted Acids, And Alkalis. Uniform, Smooth Consistency Provides For An Easy Application; Will Not Drip Or Spill Out Of Container. Long Shelf Life. Non-Setting Formula Will Not Harden, Crack Or Become Brittle. Lubricates As It Forms A Tight Pressure Seal. Inhibits Rust And Corrosion. Wipes Clean From Hands. Withstands Air/Steam Pressure To 200 Psi And Liquid Pressure To 250 Psi At Temperatures Ranging From 0 Deg F To 350 Deg F. NOT FOR LP GAS. Not For Use On Plastic Pipe Or Fittings. Certified To ANSI/NSF Standard 61, Safe For Drinking Water Lines. Meets Fed. Spec. TT-S-1732. Gray.
- Pro Dope
- Size Pint : 1/2
- Oil-Based Thread Sealant With A Uniform, Smooth Consistency For Easy Application
- Prevents Rust And Corrosion
- Do Not Use For LP Gas Lines Or On Plastic Pipe
- Wipes Clean From Hands
- Will Not Leak Or Drip Out-Of The Container
- Suitable For Use In Temperatures Ranging From 0 Degrees Fahrenheit To 350 Degrees Fahrenheit
- Use In Pipe Systems Carrying Water, Natural Gas, Air, Steam, Ammonia, Brine, Diluted Acids And Alkalis
- Designed For Use With Metal Threaded Pipe
View Details
Call for Price
PIPE THREAD COMPOUND 1/2 PINT
Use On All Metals, Plastic PVC, CPVC, ABS And Nylon Threads. Tolerates -50 F To +400 Degrees Fahrenheit; Gas To 3000 PSI, Liquid To 6000 PSI. Soft, Slow Drying, Never Seizes, Allows Easy Disassembly. SEALANT For All Types Of Gas Lines. Brushtop Bottle.
- For Lines Carrying LP, Natural Gas, & Oxygen
- Special Yellow Compound
- Size Ozs. : 8
- Soft, Slow Drying
- Never Seizes
- Allows Easy Disassembly
- Paste Lubricates All Threaded Joints, Is Non-Hardening, Non-Separating
- HarveySeal Is A Multi-Purpose Yellow Thread Compound
View Details
Call for Price
4 oz Light Yellow Liquid Soldering Flux
Oatey #11 liquid flux is formulated with a strong cleaning agent to remove corrosion quickly and effectively from surface of piping. Fluxing is a critical step in the soldering process. #11 liquid flux is lead-free and is an ideal flux for use when soldering. #11 Liquid Flux complies with CA and VT lead content regulations.
- Applicable Materials: Brass Copper Copper Coated Metal Galvanized Iron Lead Tin
- Color: Light Yellow
- Compositions: Ammonium Chloride Hydrochloric Acid Water Zinc Chloride
- Form: Liquid
- Odor/ Scent: Strong Acidic
- Package Size: 4 oz
- p H Range: 2 to 3
- Vapor Density: 1
- Viscosity: 10 cPs
- Ensures fast and effective soldering operation
- No need to clean oxidized copper
- Water soluble
View Details
Call for Price
Plumber's Putty, 14 oz
Perfect For Use On Natural Surface Materials Found In Sinks, Countertops, Strainers And Shower Bases. Remains Flexible, So It Is Easy To Work With And Cleans Up Easily.
- Size Oz : 14
- Soft, Pliable Formula
- Compatible With Stainless Steel Fixtures
- Easily Workable, Soft, Pliable Material
- Does Not Stick To Hands
- Not For Use On Plastic, Marble, Granite, Limestone Or Other Dimensional Stones
- Will Not Shrink, Crack, Harden Or Crumble
- Stainless Fixture Setting Compound
View Details
Call for Price
